CASAPPA Hydraulic Gear Pump KP30.24D

| Overview of CASAPPA Cast Iron External Hydraulic Gear Pumps (KP30.24 / KP30.29 / KP30.43)

CASAPPA KP30.24D0-A8K9-LMD/MB-N-HSC, KP30.29DO-A8K9-LMD/MB-N, and KP30.43-A8K9-LMD/MC are KAPPA 30 external gear pumps. Casappa builds the KAPPA range around a body and a mounting flange in cast iron of superior mechanical specification, and the KAPPA 30 is a solid, compact two-piece construction that allows several functions to be packed into a reduced space. Inside, the external gear pair runs on sleeve bearings between pressure-balanced thrust plates, so the assembly stays rigid and keeps its volumetric efficiency as pressure rises and as the unit wears. In the HSC Compact and standard body designs, the 24.03 cm³/rev, 29.06 cm³/rev, and 43.98 cm³/rev gear sets operate between 350 and 3,000 r/min under continuous high-pressure duty cycles.

Their function in a circuit is to draw oil from the reservoir and convert drive-shaft rotation into pressurised flow. These units carry the SAE "B" two-hole mounting flange (code K9), the SAE "B" 13-tooth spline drive shaft made for that flange (code A8) and side-positioned SAE flanged J518 ports, so inlet and outlet leave the pump on the side faces — the layout used where the pipework runs alongside the pump and the rear face stays clear. Position 2 carries D / DO: the pump is a clockwise-rotation unit, looking at the drive shaft. The 0 that follows it is the outboard-bearing position: these pumps are built without an outboard bearing, the standard configuration of the range. The same range can be ordered with European, SAE and ISO mounting flanges, nine drive-shaft options, four port positions and threaded, split-flange or flanged ports, so one pump family covers a wide spread of existing installations.

| Dimension of CASAPPA Cast Iron External Hydraulic Gear Pumps

Reference dimensions for the KP 30•24, KP 30•29, and KP 30•43 single units with the SAE "B" two-hole mounting flange (K9) and SAE flanged (SSM) side ports. The letters correspond to the dimensional drawing.

Interface data needed with the drawing:

| Pump Installation Specifications CASAPPA KP30 Series

The Casappa KAPPA 30 ordering code is a 12-position string: each position selects one characteristic of the unit, and reading it is the fastest way to check that a pump will fit an existing installation. Positions 1 to 8 define the unit itself; positions 9 to 12 define the drain port, the shaft-seal option, the body design and the painting.

Code structure — official example: KP 30•27 R 0 - 04 S3 - L OF/OD - N - OA - C4 - CSC - VNR01

Position 7 lists the port pair in IN/OUT order for pumps and in OUT/IN order for motors.

| Reading your codes: KP30.24 / KP30.29 / KP30.43

Techspecs — KP30 Series

Performance

Interfaces and configuration

Operating conditions

Advantages — CASAPPA Cast Iron External Hydraulic Gear Pumps

Cast-iron body and mounting flange

The KAPPA range is built around a body and a mounting flange in cast iron of superior mechanical specification, and the rigidity of that assembly is what holds reliability and high volumetric efficiency at high operating pressures.

High pressure from a compact body

Up to 280 bar (4,060 psi) relief-valve setting and 300 bar (4,350 psi) peak at 3,000 r/min on KP30.24, with high performance levels available across the displacement group.

Solid, compact two-piece construction

The KAPPA 30 packs several functions into a reduced space, which matters where the pump has to fit inside an existing housing or a tight driveline envelope.

Low noise emission

The external gear design keeps running noise low, which is a requirement on fan drives, municipal machinery and equipment working close to the operator.

Exceptional working life expectancy

Pressure-balanced thrust plates compensate for wear, so the pump keeps its flow as the unit ages.

High efficiency at high temperature

As the circuit oil heats up and the film thins, the cast-iron structure limits the loss of volumetric efficiency — the property Casappa specifies the KAPPA range for.

Flexible displacement selection on one frame

24.03 cm³/rev, 29.06 cm³/rev, and 43.98 cm³/rev let machine builders fine-tune circuit flow without stepping outside the standard Group 3 mounting footprint.

Explicit rotation and outboard-bearing positions

The code states D (clockwise) and 0 (without outboard bearing), so the drive direction and the shaft support arrangement are fixed at order stage rather than left to installation.

Standard SAE interface

The K9 two-hole SAE "B" flange and the A8 SAE "B" 13-tooth spline shaft match the SAE mounting and coupling that mobile machinery is built for, and the side-positioned SAE flanged J518 ports take standard split-flange fittings.

Available with built-in valves

KAPPA pumps can be ordered with integrated valve functions, which removes external plumbing from the circuit.

Wide combination choice

European, SAE and ISO mounting flanges, nine drive shafts, four port positions and threaded, split-flange or flanged ports let the same pump family be matched to an existing driveline, mounting and pipework.

Suited where fluids and size are critical

KAPPA is the range Casappa positions for applications where noise, contamination, non-flammable fluids and envelope size are the deciding factors.

6. Reference of CASAPPA KP30 Series

6.1 The KP 30 range — same series, all displacements

Every size below is a valid position 1 in the KAPPA 30 ordering code. The ratings are published as relief-valve setting p2 and peak pressure p3, with the two rating columns given where the catalogue publishes them; reversible pumps and motors are rated 15 % lower than the values shown.

The same displacements are available as gear motors in the KM 30 range, which shares the type, shaft, flange and port positions of the pump code.

6.2 Complete order numbers identified on the market

Complete KAPPA 30 pump order numbers for the KP 30 range. Reference only — each number is valid only in the exact configuration it describes.

Official Casappa order examples, for reference:

7. Brand Replacement

HENGYUHANG supplies a replacement for the CASAPPA KAPPA 30 gear pump series, including KP30.24D0-A8K9-LMD/MB-N-HSC, KP30.29DO-A8K9-LMD/MB-N, and KP30.43-A8K9-LMD/MC, as well as the rest of the KP 30 size range from KP 30•19,5 to KP 30•82, in pump and gear-motor form. The replacement is built to the same group 3 dimensional envelope and the same international standard interfaces — European, SAE and ISO mounting flanges, the same drive-shaft families, and threaded, split-flange or flanged ports — so a machine originally fitted with a Casappa KAPPA 30 pump can be returned to service without modifying the driveline, the mounting or the pipework.

Replacement units are supplied to Casappa's published interface and dimension data for the KAPPA 30 group. Fitment is decided by the ordering code of the original pump, so please quote the complete original order number when enquiring.

8. Applications of CASAPPA KP30 Series

Typical applications of the KAPPA 30 gear pump family:

Building and construction — supply pump on compact machines, excavators and loaders, roller and drum drives, auxiliary circuits

Material handling — lifting, tilting and positioning circuits on handling equipment, cranes and aerial platforms

Forestry — feed, conveyor, saw and attachment drives on forestry machinery

Fan drive — engine cooling fan drives and hydraulic fan circuits

Agriculture — supply and implement circuits on tractors, balers, harvesters, sprayers and seeders

Industrial hydraulics — presses, mixers, machine tools and plastic injection moulding machines

Special vehicles — municipal vehicles, cleaning vehicles and truck-mounted equipment

In these machines the pump feeds loads that run continuously at moderate circuit pressure, and is expected to hold flow under sustained load, high duty cycles and demanding ambient conditions. The cast-iron body, the sleeve-bearing gear pair and the pressure-balanced thrust plates are what let the unit keep its volumetric efficiency as circuit pressure and oil temperature rise.

9. Package & Shipping

10. Why Choose Hengyuhang?

A hydraulic specialist, not a general trader. Quanzhou Hengyuhang Power Technology Co., Ltd. is based in Fujian, China and manufactures hydraulic gear pumps and motors, synchronous motors, multiple pump units, pumps with built-in valves and custom valve blocks.

One-piece minimum order. MOQ is one unit, so a single machine can be put back into service without committing to a production batch.

Model-level checking before you order. Send the complete original order number — for this page, the full KP30.24..., KP30.29..., or KP30.43... string — and every position, the drive shaft, the flange and the ports are run against the KAPPA 30 data before the unit is built.

Coverage of the intermediate displacements. The KP 30•24, KP 30•29, and KP 30•43 of this page represent standard and intermediate sizes, and the same plant covers the range from KP 30•19,5 up to KP 30•82.

In-house production and testing. CNC machining centres, automatic gear heat-treatment lines, single-piece-flow assembly and an automatic hydraulic test bench, with ERP/MES traceability through production.

Replacement coverage across the range. The same plant supplies replacement units for a wide list of hydraulic brands and models, which keeps a mixed machine fleet on one supplier.

Customization support. OEM, ODM and OBM are offered, and customized packaging, graphics, nameplate and logo are available for distributor orders.

One-year warranty. Every unit is covered by a one-year warranty.

Responsive after-sales. Online support for installation and application questions.